Bottle Chassis by RAI - with Gauge hole in bottom of stock
Only a few left!
Custom designed Bottle Chassis by R. Arms Innovations for D.I.Y. 'Bottle Gun' conversions for your Benjamin Marauder PCP.
used on Gen 2 Marauder rifles, Our short tube works with both Gen Marauder Rifles.
Drop Block by RAI for Bottle gun conversions of Benjamin Marauder
Custom designed Drop Block by R. Arms Innovations for D.I.Y. 'Bottle Gun' conversions with the Benjamin Marauder.
ASTM 825-14 NGO thread is a common thread for use with the Ninja Paintball regulators and CO2 tanks.
Thread for air tube is the same thread used on the stock Marauder air tube.
works with Brass Bottle Adapter by RAI - Metric M8-1.5 and Inch 5/8-18 options
Brass Bottle Adapter by RAI - Metric M8-1.5 and Inch 5/8-18 options
Custom designed Brass Bottle Adapter by R. Arms Innovations for D.I.Y. 'Bottle Gun' conversions for your Benjamin Marauder PCP.
Does include o-ring (not shown)
One end is a standard paintball / CO2 thread and o-ring.
the other end is for the bottle of your choice either metric M8-1.5 or inch 5/8-18
works with Drop Block by RAI for Bottle gun conversions of Benjamin Marauder
Dust Cap by RAI
Only a few left!
On Sale
On Sale
Check Valve - make foster quick disconnect
Fill Valve for D.I.Y. 'Bottle Gun' conversions for your Benjamin Marauder PCP.
On Sale
On Sale
Plastic Trigger Guard for RAI bottle gun conversion
Plastic Trigger Guard for D.I.Y. 'Bottle Gun' conversions for your Benjamin Marauder PCP.
actual product may vary from image shown depending on available stock
Bottle Chassis by RAI - No Gauge Hole - Gen 2 only
Only a few left!
Custom designed Bottle Chassis by R. Arms Innovations for D.I.Y. 'Bottle Gun' conversions for your Benjamin Marauder PCP.
This version doesn't have a gauge hole in the bottom of the stock, Gauge must be mounted in the drop block, Only fits on Gen 2 Marauder rifles.
Our short tube works with both Gen Marauder Rifles.
On Sale
On Sale
Air Tube by RAI - gauge hole marked not drilled for Gen 2 Marauder Rifle Conversion
Custom designed Air Tube by R. Arms Innovations for D.I.Y. 'Bottle Gun' conversions for your Benjamin Marauder PCP Rifle.
Made from .092 Chrome-Molly Steel
New design with gauge hole location marked but not drilled. Can be used with gauge in stock and gauge in drop block builds.
Two 3.87" Picatinny Rails , screw on aluminum
- Two 3.87" Picatinny Rails Each with 7 Numbered Slots
- 2 Screw Holes on Each Rail
- Complete with 5 Hex Screws and Allen Wrench
- Weight 2.3 oz
- Material: Aluminum
- For the Marauder pistol install seen on our website, you many need to get creative with hardware that isn't included with this kit.
Check Out These Regulators:
2000 psi Ninja Regulator
Only a few left!
NINJAREG45KX 4.5k to 2k psi regulator
NOT FOR PAINTBALL
high pressure fill station for nitrogen up to 6000 psi input 1-5000 psi output cga-677
Only a few left!
THE FILL STATION IS INTENDED FOR USE WITH NITROGEN, HPA (HIGH PRESSURE AIR), AND ANY OF THE OTHER COMMONLY AVAILABLE INERT GASES. UNDER NO CIRCUMSTANCES SHOULD THIS FILL STATION BE USED WITH OXYGEN!!! THIS UNIT IS ALSO NOT CERTIFIED FOR USE WITH COMBUSTIBLE, CORROSIVE, OR TOXIC GASES.
SPECIFICATIONS
MAX INPUT PRESSURE 6000 PSI
MAX RATED OUTPUT PRESSURE 5000 PSI
RANGE OF ADJUSTMENT 0 – 5000 PSI
GAS COMPATIBILITY NITROGEN or HIGH PRESSURE AIR (HPA)
CGA FITTING CGA 677 LEFT HANDED THREAD CONNECTION FOR BULK TANK
OPPOSITE END FOR FILL STATION ¼” -18 NPT
(4501-6000 PSI Nitrogen)
STANDARD GAUGES BULK TANK 0-6000 PSI 1/8-27 NPT
OUTPUT 0-6000 PSI 1/8-27 NPT
FILL ADAPTOR STAINLESS STEEL FOSTER 5000 PSI RATED “QD” TYPE
