Imported for you by New England Airgun
The Huben K1 is delivered from the factory with the black synthetic stock. ( we have some fancy aftermarket stocks see below! )
11/14/2020 Huben K1 .25's have arrived just in time for the Holidays!
all have tank gauges and are ready for pickup or shipped to you. Huben 5000 psi hand pumps, Boat-tailed slugs, Pellets, Custom stocks, compressors.. also available Pick Here for Options and to Order
|
We ship airguns within the United States and only where airguns are allowed. Must be 18+ to purchase. Buy purchasing thru this website you are certifying that you are 18+ and can legally own this product.
Pick Here for Options and to Order |
Yes, the .25 cal magazines too have rifling guides and our hand cast slugs do snap properly into them.
Another old wives tale, you can't unload the huben magazine! ohh yes you can.. or at least we can. watch and see how easy it is.
Your Huben K1 isn't like other air rifles where you have to force off the fill cap... The fill cap shouldn't be pulled off... it slides out of the way, pretty easy, but if you do force it... it will come off and the springs and ball bearings that hold it on will spring out (you will need a magnet to find them, they are very small)
Huben does give you one chance to recover from this... extra springs and balls are included in the spare O-ring kit. |
If your compressor or hand-pump doesn't have moisture removal capability or you just want more protection for the internals of your K1, this might be the option for you. You loose the ability to have a pressure gauge on your gun, but most pumps and compressors have better quality gauges on them and you know your pressure when your filling. With a bit of practice and experience you will know if you can shoot 1 mag or 10 mags before you should refill, so a gauge on the rifle really isn't needed. This assembly comes with some moisture capturing material, I could be paper, cotton, desicant, what ever material you have available can give you added moisture protection. This is all external to the high pressure tanks and no tools are needed to inspect and change the moisture trapping material. What Huben do you have? What Gen Huben?.... we don't know.... Huben doesn't use "Gen" to distinguish it's models, but here is how it works.
This is how the Huben K1 Serial Number is configured, there are 7 pieces of information here 1 - 2 - 3 - 4 - 5 - 6 - 7: CC-K1-YYYY-S-MM-DD-XXX
25-K1-2021-B-01-20-001
25K12021B0120001 |
- Always keep your air tank pressure higher than your regulator pressure. Default regulator setting is approx. 17mpa, it's best to keep your tank pressure between 20-30mpa for high power shooting,
- The power wheel adjustment is a fine adjust of your internal regulator pressure. 20-25 clicks from closed is a good starting point.
- The internal regulator pressure controls the force used to turn your magazine. Pellets above the surface of the magazine can cause drag pressure that keeps the magazine from turning or partially turning and can cause high pressure air to blow-out from the magazine area. (always wear ear protection)
- Additional noise suppression can adversely affect the operation of your Huben K1, The rifle is very adequately suppressed from the factory.
What the Huben K1 likes to Eat:
Boat-tail slugs are available again at New England Airgun!
We have taken over the supply to keep up with your demands,
We now mold them ourselves in: .22 @ 35 gr x (10.66) long x .217 (5.52) body .223 (5.67) dia seal. .22 @ 35 gr x (10.66) long x .218 (5.55) body .223 (5.67) dia seal. .25 @ 47 gr x (10.86) long x .250 (6.35) body .253 (6.45) dia seal. |
Order Huben Boat-Tail Pellets Below |
Huben Hand Pumps In-Stock as of 6/1/2020
|
|
.22 cal. with Black Synthetic stock.
made for .22 slugs but shoots pellets too!
430 fps to 1480 fps with H@N Baracuda Green 12.96 grain.
(That is up to 63 fpe with lead-free "Tin" pellets)
(27 fpe @ 980 fps for best accuracy)
980 fps (75fpe) recommended
with 35.3 grain slugs.
We recommend the same fps with the lead-free pellets too, just turn down the power wheel and tune it to your pellet of choice.
We do not provide estimates but will contact you if we feel the repair is extensive and requires your authorization. Time for repair may be unreasonable (we all have day jobs outside of our airgun businesses)... parts are coming from china we may combine them with other orders to save on shipping costs and other fees. Life Happens to us too.
if you wish to pay an expediting fee to meet your short time demands, please let us know and we will bill you in advance adding plenty of cushion to cover any and all unexpected costs. (you might be paying for a new gun... (reality hurts). If we have to make custom parts the cost might be more than a new gun.